Skip to content
Free Training and Installation on Pressure Washers over £2000
Contact Us 01525 370 795
Chewing Gum Removal Machine

Cold Water Will Never Beat A Pavement Full Of Gum

Walk down any high street and look at the paving. Those grey dots are chewing gum, trodden flat and baked on by several summers.

Most teams try to blast them off with cold water, and the dots are still there tomorrow.

The problem is not the operator or the pressure. It is the temperature, which decides almost everything that follows.

Why cold water only moves gum around

Chewing gum is a soft polymer with sticky resins, and after months underfoot it bonds hard to the stone.

Cold water makes gum harder. It turns stiff and rubbery, so the jet bounces off or tears it into an ugly smear.

More pressure is not the answer. Push the jet hard enough to shift cold gum and you start cutting into the paving instead.

Heat changes the gum itself. Warm it up and the resins soften, the bond weakens and a gentler jet lifts it clean away.

That is why a proper chewing gum removal machine is, at heart, a heating machine. The pressure only finishes the job that the heat started.

For councils, universities and town centre managers, that matters for budgets as well as results. A heated machine clears more pavement per shift and leaves fewer return visits.

What heat does on the street

A hot water pressure washer heats the water through a burner coil before it reaches the lance. Some street machines go further and run at steam temperatures for the toughest gum.

Hotter water needs less pressure. You can turn the pressure down and still lift gum, which protects the surface underneath.

Heat also shifts the grime around the gum. Spilt drinks, food grease and traffic film all respond better to hot water. Our guide on hot versus cold for grease explains why.

Give the heat a moment. Hold the jet on a stubborn piece for a few seconds, because rushing a hot machine wastes its advantage.

Surface cleaners for open paving

A lance is fine for odd patches, but a whole precinct needs something faster and more even.

A flat surface cleaner spins two jets under a hood. It covers a wide strip in one pass and keeps the spray off shop windows and passers by.

It leaves no stripes. Hand lances often leave zebra marks on paving, while a rotary head holds the same distance across the whole job.

Pair it with hot water for gum work. The heat softens the gum and the spinning head lifts it, then the lance finishes the stubborn spots.

Our roundup of the best flat surface cleaners for trade use covers sizes and fittings.

Protecting block paving, soft stone and brick

Town centres are full of delicate surfaces, and permanent damage costs far more than removing the gum.

Block paving joints wash out fast. A concentrated jet at close range strips the jointing sand, and the blocks gradually loosen. Keep the jet moving and work across the joints, not along them.

Soft stone and old brick erode. Sandstone, limestone and historic soft bricks can pit or scar under an aggressive jet. Once the face has gone, it does not come back.

Always run a test patch first. Try your settings in a quiet corner, then check it once dry, because wet stone hides marks.

Lower the pressure and widen the angle. A wider fan spreads the force over more surface. Our nozzle guide shows which tip suits which job.

Stand back a little further. Distance softens the impact more than most people expect, so move closer only if the gum refuses to shift.

Gum and Graffiti: Hot Water Pressure Washer Removal Guide

Graffiti needs speed and the right chemical

Graffiti is a different job, because gum sits on top of the surface while paint soaks into it.

Act fast. Fresh paint has not yet cured or sunk deep into the pores. Leave it a few weeks and removal takes longer and risks more damage.

Paint type matters. Spray paint, marker pen, emulsion and permanent ink each react in their own way to a given remover.

Chemical first, then rinse. Apply a suitable graffiti remover and let it work for its full dwell time. Then rinse it off with hot water at low pressure.

Do not try to blast it off. Pressure alone drives pigment further into brick and stone, and can leave a ghost outline worse than the tag.

Ask your supplier which cleaning chemicals and detergents suit the surface and the paint. Always check the safety data sheet before use.

Anti-graffiti coatings stop the next one

Removing a tag is half the job. On walls that get hit again and again, a coating saves time on every later visit.

Sacrificial coatings come off with the graffiti. You wash the paint and the coating away together, then reapply.

Permanent coatings stay put. The paint cannot bond to the wall, so it washes off with hot water and a mild cleaner.

Pick the coating to suit the wall. Some coatings alter the appearance of porous stone or stop older brickwork from breathing. Listed buildings may need consent, so check with your conservation officer first.

Working safely in public spaces

Street cleaning happens around shoppers, pupils and staff, which changes how you set up the job.

Cordon off the work area. Barriers and signs keep people clear of the spray and trailing hoses, and wet paving gets slippery at the edges.

Think about noise and timing. Petrol engines and diesel burners are noticeable near residential properties. Many councils and campuses book this work for early mornings, before footfall picks up.

Watch where the water goes. Wash water containing gum residue, grime and chemical should never enter surface water drains. Cover nearby gullies and check the local rules with your water company or council.

Protect the operators. Hot water and steam burn, so they need proper gloves, eye protection and boots, plus training before working alone.

Kit for a council or campus van

A street team needs a setup that is quick to deploy and easy to move between sites.

Choose the power source by location. Petrol suits highways and car parks with no electricity supply nearby. Electric is quieter and cleaner, which helps in precincts, schools and covered spaces.

Look at zero emission options for enclosed areas. Some fully electric machines can heat water too, so they suit early starts near housing. Our guide to electric versus petrol pressure washers sets out the trade offs.

Build it as a van pack. A water tank, a hot machine, a hose reel and a surface cleaner, all fixed in place. Our guide to the best van pack pressure washers covers layouts.

Keep the burner serviced. A hot machine that will not fire is a heavy cold machine, so book a service before the busy season.

Frequently asked questions

Why does cold water not remove chewing gum?

Cold water makes gum stiff and rubbery, so the jet tears it or smears it rather than lifting it. Heat softens the gum and breaks its bond with the paving.

Will hot water damage block paving?

Heat on its own is not the main risk. The danger comes from high pressure and a tight jet washing out the joint sand. Use a wide angle, lower pressure and a test patch.

What is the best way to remove graffiti from brick?

Act quickly, identify the paint and apply a suitable remover first. Let it dwell, then rinse with hot water at low pressure. Avoid blasting, which pushes pigment deeper.

Should a council choose petrol or electric?

Petrol suits open roads with no power supply. Electric suits precincts, schools and covered areas where noise and fumes matter.

Can you service our existing street cleaning machines?

Yes. We service Kranzle, BOSS BOYS, Karcher, Nilfisk, Ehrle and Interpump machines. Our mobile engineers can visit, or you can drop machines at our Leighton Buzzard workshop.

The bottom line

Gum and graffiti come off with heat, the right chemical and patience, not raw pressure.

Test first, turn the pressure down and widen the angle on any surface you would struggle to replace.

Then fit a van with the right power source, keep the burner serviced and plan where the water will go.

RealKleen has supplied and serviced professional cleaning equipment since 1980. We work from 13 Harmill Industrial Estate on Grovebury Road in Leighton Buzzard, Monday to Friday, 8:00 to 16:45.

Our mobile engineers cover a seventy-five-mile radius. Tell us about your streets, and we will help you build a kit that leaves the paving clean and whole.

Previous article Wash The Hull Before The Weed Dries, Or Wash It Twice
Next article Can Pressure Washer Pumps Be Repaired? When It Pays

Call RealKleen

01525 370 795 Mon-Fri 8:00-16:45