Skip to content
Free Training and Installation on Pressure Washers over £2000
Contact Us 01525 370 795
Pressure Washer Wash Water Disposal

The Drain In Your Yard Probably Goes Straight To A River

Most yards have a drain in the middle. Somebody washes a van next to it, the foam runs in, and the job looks finished.

It is not finished. The water has only just set off, and nobody on site knows where it ends up.

That question matters more than the machine, the chemical or the nozzle. Get it wrong and the cleaning becomes a pollution problem with your name on it.

Two kinds of drain, and they look the same

Every commercial site has two separate drainage systems, and from above they look identical.

Surface water drains take rain. They run to a stream, a river, a ditch or a soakaway. Nothing treats that water on the way.

Foul drains take sewage. They run to a treatment works, where the water company cleans it before release.

A grid in the middle of the yard is usually a surface drain. A gully by the toilet block is usually foul. Usually is the problem, because plenty of older sites have the two connected the wrong way round.

Check the drainage plan before the first wash. If the site has none, a dye test settles it in an afternoon. Pour coloured dye into the drain and see where it comes out.

Wash water is not rain

Rinsing a clean car with plain water is one thing. A working fleet is another.

Vehicle wash water carries oil, diesel, brake dust, road grime, silt and detergent. On a farm it carries muck. On a food site it carries fat.

All of that counts as trade effluent. It does not belong in a surface drain, whatever the size of the job.

The detergent is the part people forget. Traffic film remover works because it breaks oil into tiny droplets. That is exactly what you want on the panel, and the last thing you want in a watercourse.

If you mix your own, our guide to traffic film remover dilution helps you use less of it. Less chemical in means less chemical out.

Why the interceptor will not save you

Plenty of yards have an oil interceptor on the surface drain. Site managers often assume it covers the wash bay too.

It does not, and the reason comes down to simple chemistry.

An interceptor separates oil by letting it float. Water passes underneath, and the oil stays trapped on top for emptying.

Detergent stops oil from floating. It holds the oil in suspension, so the whole mixture passes straight through the interceptor and out the other side.

So an interceptor sized for spills on a car park does little against a wash bay running TFR every day. It also needs regular emptying, which many sites forget for years.

Where the water can go

Broadly, you have three routes. The right one depends on the site, the volume and the dirt.

To the foul sewer, with permission. This needs a trade effluent consent from your local water company. They set limits on what you send and may ask for a silt trap or separator first.

Into a recycling system. The water passes through settlement and filtration, then returns to the machine. Busy wash bays often save enough water to justify the kit.

Into a sealed tank for collection. A licensed waste carrier takes it away. This suits low volume sites with no foul connection nearby.

Whichever route you take, keep the paperwork. Consents, collection notes and maintenance records are what an inspector will ask to see.

Our wash bay design guide covers the falls, gullies and silt traps in more detail.

Where the Water Goes: 5 Drainage Checks Before Pressure Washing

Mobile work is where it goes wrong

A fixed wash bay gets designed once. Mobile work gets decided in the car park, ten minutes before the start.

Ask where the water will go at the quoting stage. Not on the morning. The answer changes the setup and sometimes the price.

Carry drain covers or bungs. A mat over the nearest surface drain stops the run-off at the obvious point.

Use a bund or recovery mat for heavy jobs. It holds the water so you can pump it to a tank or a foul point.

Do not wash near a watercourse. Ditches beside farm tracks and rural lay-bys are the worst places for it.

The choice between static and mobile systems is partly a water question. A fixed bay can be plumbed properly once. A van pack has to solve it on every job.

Use less, and less goes down

The cheapest way to manage wash water is to make less of it.

A higher pressure machine at the right flow uses less water per vehicle. More is not always better on a dirty panel. The right nozzle often matters more than a bigger pump.

Hot water cuts both water and chemical. Heat shifts grease that cold water only moves around, so you rinse less and dose less.

Pre-soak and wait. Let the chemical work for its dwell time instead of blasting it off at once. You use half the water and get a better finish.

Sweep before you wash. Dry silt and debris belong in a bin, not in the drain. Our guide to removing oil from concrete covers the same point for yard floors.

Farms and food sites carry a heavier load

Vehicle grime is only one kind of dirt. Agricultural and food processing sites send something far stronger towards the drains.

Slurry and muck wash water is highly polluting. Even small volumes can strip the oxygen from a stream and kill the fish downstream. On farms it belongs in the dirty water system or the slurry store, never the yard drain.

Fat and protein from food sites block sewers and overload treatment. Water companies often set tighter limits for these sites, and a grease trap is usually a condition of consent.

Disinfectants and sanitisers add another layer. They are designed to kill organisms, which is exactly the problem once they reach a watercourse.

Our guides to farm washdown equipment and food site washdown cover the machines. The drainage question comes first in both cases.

Pick the chemical with the drain in mind

Chemicals differ in how hard they are on the system downstream.

Ask the supplier what happens after the rinse. Some products separate faster once they settle. That helps an interceptor or a recycling plant do its job.

Match the product to the dirt. A strong caustic product on a lightly soiled car only adds load to the drain. Our guide to choosing washdown chemicals sets out which one suits which job.

Store it bunded. A split drum near a surface drain is a spill, not a wash.

Frequently asked questions

Can I wash vans into a surface water drain?

No. Surface drains often run straight to a watercourse without treatment.

Wash water carrying oil, silt or detergent belongs in a consented foul sewer, a recycling system or a sealed tank.

Does an oil interceptor handle wash water?

Not properly. Detergents keep oil in suspension, so it passes through the interceptor instead of floating to the top. An interceptor suits spills and rainwater, not daily washing with TFR.

What is a trade effluent consent?

Permission from your water company to send wash water to the foul sewer. They set limits on what the water contains and may require a silt trap or separator before the connection.

How do I find out where my drains go?

Check the site drainage plan first. If there is none, a dye test shows where each drain comes out. Do it before the first wash rather than after a complaint.

Can you help set up a wash area?

Yes. We supply the machines, the chemicals and the accessories, and we can talk through the layout. Tell us the site, the vehicles and where your water connects.

The bottom line

The drain in the yard is not the end of the job. It is where the water sets off, and you are responsible for where it ends up.

Find out which drains are surface and which are foul before anybody picks up a lance.

Then pick a route, keep the paperwork and use less water and chemical wherever you can.

RealKleen has supplied and serviced professional cleaning equipment since 1980. We work from 13 Harmill Industrial Estate on Grovebury Road in Leighton Buzzard, Monday to Friday, 8:00 to 16:45.

Our mobile engineers cover a seventy-five-mile radius. Tell us about your site, and we will help you plan a wash that spares the river.

Previous article Your Hot Washer Has Gone Cold, And The Burner Is Rarely To Blame
Next article How to Prevent Washer Downtime on Every Job

Call RealKleen

01525 370 795 Mon-Fri 8:00-16:45